JUST HOW TO REPLACE A BATHTUB IN YOUR BATHROOM

Just How to Replace a Bathtub in Your Bathroom

Just How to Replace a Bathtub in Your Bathroom

Blog Article

Schedule Your Job Now

Presented here below you will discover lots of incredibly good data on the subject of A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently easily accessible, the job can relocate rapidly; if you have to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will require a helper to move out the old bathtub and also embeded in the new one. Ensure you have certified on your own for the task as well as are comfortable trying it. As opposed to employing a professional to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you might need a professional plumber to make tube links.
This post will help you mount a brand-new bathtub in your bathroom if you have actually already acquired a brand-new tub and also do not require to change the setup of your previous water system pipelines.
Your devices and product list ought to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installation


    To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to avoid strain on the tub.
    Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.

    Removing Old Taps


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is frequently the situation.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
    Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

    Installing the Bathtub


    Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub till the level checks out level.
    To install faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression join; after that do the very same for the various other tap.
    Switch on the water and also inspect all joints as well as new pipework for leakages and also tighten them if required. Fill the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub ought to wait till the tub has been utilized at least when as this will certainly settle it right into its final position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
    If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the faucet as well as the sink. Secure the tap in position with the maker given backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
    You can select from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split rather very early if you do not take into account this motion prior to securing.
    Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the tiles using water-resistant or water resistant sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a remark below. We would be pleased to find out your ideas about this entry. We are looking forward that you visit us again soon. Remember to take a moment to share this article if you liked it. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .



    Check It Out

    Report this page